What size water softener do I need?

The right size comes from three numbers: how hard your water is, how much you use, and how often you want it to regenerate.

Short answer: most 3 to 4 person homes land between 32,000 and 48,000 grains. Run your own numbers below.

  1. 1Household
  2. 2Your water
  3. 3Your result

Who uses the water?

Count everyone who lives in the home most of the time.
Advanced: daily water use and salt price
Default 75. EPA WaterSense reports the average American uses roughly 82 gallons a day at home; lower it for a frugal household.
An editable assumption used only for the annual cost estimate.
Fill in the fields for an instant estimate.
Planning estimates only. Verify your numbers with a certified lab test, and have any installation done by a licensed plumber. Results are estimates, not engineering, plumbing, medical, or legal advice, and no health claims are made. See the terms.

The guide

How to size a softener in four steps

  1. Get your hardness. Use a utility report, lab test or the hardness lookup. Convert mg/L to gpg by dividing by 17.1.
  2. Add iron compensation. Add 3 gpg for each 1 ppm of iron.
  3. Estimate daily water use. People x 75 gallons per day, or your own number.
  4. Multiply and round up. Compensated hardness x gallons per day x 7 days, then round up to 24k, 32k, 48k or 64k grains.

Worked example: 4 people, 15 gpg, no iron. Gallons per day = 4 x 75 = 300. Grains per day = 15 x 300 = 4,500. A 7-day cycle needs 31,500 grains, so the next standard size is 32,000 grains, which regenerates about every 7.1 days.

Source: USGS Water Science School: Hardness of Water Source: NSF/ANSI 44: Residential cation exchange water softeners (NSF)

Recommended size by household and hardness

People3 gpg5 gpg7 gpg10 gpg15 gpg20 gpg25 gpg
124k24k24k24k24k24k24k
224k24k24k24k24k24k32k
324k24k24k24k24k32k48k
424k24k24k24k32k48k64k
524k24k24k32k48k64k64k+
624k24k24k32k48k64k64k+

Assumes 75 gallons per person per day, no iron and a 7-day regeneration target. "k" = 1,000 grains; "64k+" means demand exceeds the largest standard size, so consider a dual-tank unit or ask a plumber. Add 3 gpg per ppm of iron to your hardness before reading the chart.

What goes wrong

  • Ignoring iron. It uses up capacity, so the unit regenerates early.
  • Mixing units. Labs often report mg/L; sizing uses gpg. Divide mg/L by 17.1.
  • Using city averages for a private well. Wells vary house to house; test yours.
  • Sizing only on capacity. Check the rated service flow against your peak GPM.
  • Buying on brand or marketing claims instead of the grains-per-day math.

Frequently asked questions

What size water softener do I need for a family of four?

It depends on hardness. At 5 gpg a 24,000-grain unit is enough; at 10 or 15 gpg a 32,000-grain unit; at 20 gpg a 48,000-grain unit (see the chart). Use the calculator for your exact numbers.

Is bigger always better?

No. An oversized unit regenerates less often, which saves salt per regeneration but costs more up front and may sit long between cycles. Sizing to roughly a 7-day cycle is the usual target.

Do I add iron to the hardness number?

Yes for sizing: add 3 gpg for each 1 ppm of iron. If iron is above about 2 ppm, plan an iron filter first.

What about flow rate?

Capacity is only half of sizing. The softener's service flow rate must also cover your peak demand. Compare it with the GPM from the filter calculator.

Sources